VMC 1100

7" All-In-One Vehicle Computer with Touch Screen and Multifunctional Tracker
  • Main Feature
  • 7" WVGA TFT LCD Monitor with resistive touch screen
  • Built-in Intel Atom® Dual Core E3825 1.33GHz
  • Compact and fanless design
  • On screen programmable F1 ~ F5 function keys
  • Support GPS/WWAN tracker function for car-safety
  • RFID for ID identification
  • Built-in GPS (Option: Dead Reckoning Support)
  • GPS/WLAN/WWAN for wireless communication
  • Dual CAN bus 2.0B and optional OBDII (SAE J1939) for car diagnostic
  • Wide Range DC input from 9 ~ 36V
  • Military standard for vibration and shock
  • SAE J1113, ISO7637-2 and SAE J1455 conformity for power design
  • CE/FCC/EMark
Add to Inquiry
Datasheet(PDF)
General Cooling System: Fanless Enclosure: Plastic PC + ABS with aluminum die casting heatsink Mounting: Support VESA 75, stand mounting Four SMA Type antenna connectors of BT/Wi-Fi/WWAN/GPS Power Input: 9 ~ 36VDC input with Ignition Power Consumption: 26W Ingress Protection: Front panel IP54 Dimension: 213mm (W) x 145mm (H) x 50mm (D)(8.3" x 5.7" x 1.9") Weight:
N.W: 1.3Kg
G.W: 1.6Kg
LCD Panel 7-inch TFT LCD Panel with LED Backlight 800 x 480 pixels (WVGA) Brightness: 400 cd/m² (typical) Contrast ratio: 600:1 (typical)
Touch Screen Sensor 4-wire resistant touch Anti-glare coating surface Transmission rate: 78 ± 3%
CPU & Chipset Intel® Atom™ Dual Core E3825 1.33GHz
Memory One 204-pin DDR3L 1600MHz SO-DIMM slot (up to 4GB)
- Default 4GB
Expandable Storage 1 x SATAIII SATA DOM Slot (available option 16GB / 32GB / 64GB)
Expansion 1 x Half size mini-PCIe socket (USB 2.0, PCIe 2.0) 1 x Full size mini-PCIe socket (USB 2.0, UART) for LTE module with 1 x external Mini-SIM 1 x External module for OBD/RFID module option (USB 2.0, UART)
I/O Interface-Front F1 ~ F5 functions key Light Sensor Internal Mic-in 2 x Built-in 2W speakers 3 x LED indicators (Power mode, Storage and WWAN status)
I/O Interface-Lateral Right side
- 1 x Micro SD card socket
- 1 x SIM card socket
- 1 x USB 3.0 host type A connector
- 1 x Mic-in, Line-out Left side
- 1 x Power button
- 1 x System reset button
- Volume up/down or Brightness up/dow
I/O Interface-Rear 1 x 5-pin Circular connector for Power/Ignition input 1 x RJ45 for LAN 1 x RJ45 for Full RS-232 with 0V/5V/12V power supply (0.5A) 1 x DB9 (Male) for
- RX/TX or RS-485
- 2 x CAN Bus 2.0 1 x DB15 (Female) for
- GPS dead reckoning interface (optional)
- 2 x PWM, 2 x Analog Input, 2 x GPO, 2 x GPI
 Analog Input requirement for Voltages are measured
 Channel: 2
 Voltage range: 0 ~ 38V
 Resolution: 8 bit
 Input requirement for frequency, speed
 Square wave
 Channel: 2
 Frequency signal offset voltage range: 0~15VDC, 1Hz~5KHz
 Protection: +/- 500V spike
 Frequency signal duty cycle range: 10% ~ 90%
Communication Module 1 x u-blox NEO-M8N module
(support GPS/Gloness/QZSS/Galileo/Beidou) 1 x WLAN or Bluetooth module for optional 1 x WWAN module for optional
Power Management Selectable boot-up & shut-down voltage for low power protection HW design ready for 8-level delay time on/off at user's self configuration Power on/off ignition, software detectable Support S3 and S4 suspend mode; wake on RTC and SMS
Operating System Windows 10 Windows 8 Professional, WES8 Windows 7, WES7 Linux Fedora (kernel V3.2.0)
Environment Operating temperatures: Ambient with air -20°C to 60°C Storage temperatures: -30°C to 80°C Relative humidity: 10% to 95% (non-condensing) Vibration (random): 3g @5 ~ 500Hz Vibration
Operating: MIL-STD-810G, 514.6 Procedure 1, Category 4
Storage: MIL-STD-810G, 514.6 Procedure 1, Category 24 Shock
Operating: MIL-STD-810G, Method 516.6, Procedure I, trucks and semi-trailers=20g
Crash hazard: MIL-STD-810G, Method 516.6, Procedure V, ground equipment=75g
Power Design & Protection Load dump and inductive load protection Cold cranking protection Transient voltage protection Electrostatic discharge protection
Standards/Certifications EMC
- CE, FCC class B, E-Mark Power
- SAE J1113
- SAE J1455
- ISO 7637-2
Add to Inquiry
Take a minute and tell us what you think!