Specifications
| CPU Support | - AMD Geode™ LX800,500 MHz on Board
- 128 KB L2 cache (64 KB I-cache/64 KB D-cache)
|
| Main Memory | - 1 x 200-pin SO-DIMM socket, up to 1GB Non-ECC/Non-Registered DDR SDRAM (64-bit, 200 MHz)
|
| Chipset | - AMD Geode LX800 / AMD CS 5536
|
| BIOS | - Award system BIOS
- Plug & Play support
- Advanced Power Management and Advanced Confi guration & Power Interface support
- 4M bits fl ash ROM ACPI
- ACPI support: Only support Software Shutdown by 5Vsb Provided
|
| On-board LAN | - 1 x Realtek 8139C+ 10/100 Fast Ethernet Controller
- Supports Boot From LAN (PXE)
- Supports Wake on LAN by 5usb provided
- 1 x RJ45 with LED
|
| Display | - The Geode™ LX800 integrated Graphic, supports both standard VGA and TFT
- Analog VGA Interface: 1 x DB15 VGA port CRT Supports up to 1920x1440x32 bpp at 85 Hz
- TTL Interface: TTL LCD supports up to 24bit, 1600x1200x32 bpp at 60 Hz for TFT
|
| Audio | - REALTEK,ALC203 CODEC for AC97 v. 2.0
- Mic in and Speaker out connector, Line in with pin header
|
| I/O Interface | - 4 x USB 2.0 port (USB 1/2 on front, USB 3/4 via one JST connector), bandwidth: 480 Mb/s
- 2 x SIO, 16C550 UARTs (One on DB9 edge connector support RS-232, one onboard with pin header support RS-232/422/485)
- Parallel ports:Bi-directional, EPP/ECP support, 1 x Box header 26-pin connector
- PS/2: 1 x 6-pin 2.0mm JST Box Header
- IrDA: 1 x 5-pin Box Header for IrDA,TX,RX
- On Board buzzer: two x 2 pin header for Reset switch and Power Button, two x 2 pin header Power LED and HDD LED, 1 x 3 pin 2.0mm pin header for SMBUS and I2C
|
| Storage Support | - 1 x CF Internal socket Support One Type I& II Compact Flash Card (Primary Master)
- 1 x IDE 44-pin connector,supports Ultra DMA 33/66/100 1 x 2-pin IDE Active LED Header
|
| Watchdog Timer | - Watchdog Timer is programmable by software from 0 to 255 seconds and from 0 minute to 255 minutes (Tolerance 15% under room temperature 25°C)
|
| On-board RTC | - On chip RTC with battery back up
- 1 x External Li-ion Battery
|
| Power Requirements | - Supports both AT and ATX Mode (BIOS and H/W is default to AT mode)
- AT Mode: +5V Power in,No Power On push Button, Software Shutdown function and LAN remote wake up. Power requirement:+5V; Full-Loading Mode:1.55A; Light loading Mode:1A
- ATX Mode: Power Required: +5V / -5V / 5Vsb Power In When Change to ATX Mode, the BIOS default setting is as follow:POWER -SUPPLY TYPE -->[ATX], AUTO PWR-FAILURE RESUME-->[ON]
|
| Dimensions | - 3.5" form factor, 146 mm (L) x 105 mm (W) (5.7" x 4.1")
|
| Environment | - Board level operating temperature: 0°C to 60°C
- Storage temperature: -20°C to 85°C
- Relative humidity: 10% to 90% (Non-condensing)
|
| Certifications | |