Specifications
| CPU Support | - Supports Intel® Celeron® M 600 MHz processor with 512 KB L2 cache and 400 MHz FSB
- Support for Intel® Pentium® M processor or Intel® Celeron® M processor in 478-pin, Micro-FCPGA package (mPGA479M Socket)
|
| Main Memory | - On-board 256 MB Non-ECC DDR SDRAM memory
|
| Chipset | - Intel® 852GM 400 MHz
- Intel® ICH4
|
| BIOS | - Award system BIOS
- ACPI: Only supports Software Shutdown by 5 Vsb Provided (S0 /S5 only)
- Advanced Power Management support
- 4 Mbit fl ash ROM
- Supports Pentium M Speed Step (Customized by Nexcom)
- Supports Automatic Power On Function
|
| On-board LAN | - Realtek RTL 8110SC Gigabit Ethernet Controller
- 1 x RJ45 with LED
- Supports PXE LAN boot ROM for Ethernet Boot up
- Supports Wake on LAN (When 5 Vsb power available)
|
| Display | - Intel® 852GM integrated graphics solution w/ Intel® Extreme Graphics 2 technology, up to 64 MB of dynamic video memory allocation
- Analog VGA Interface:1 x DB15 VGA port, 350 MHz integrated 24-bit RAMDAC that can drive a standard progressive scan analog monitor with pixel resolutions up to 1600 x 1200 at 85 Hz, 2048 x 536 at 75 Hz
- LVDS Interface:DF13 20-pin LVDS connector for internal connection, supports single(18bit/24bit) LVDS panel, wide screen resolution up to 848 x 480 and 1366 x 768
|
| I/O Interface | - Serial port: 1 port, with 16 C550 UARTs, 1 x DB-9 Connector
- USB 2.0: 6 ports, with two direct output, four from 1x6 JST
- On-board 3-pin header for I2C, one pin for GND
- On-board 2-pin header for Reset switch
- 8 GPIO lines via header (GPI 0 ~ 3 and GPO0 ~ 3) TTL Level (0/5 V)
- On-board Power LED and HDD Active LED Pin Header
- Reserved 1 x 3-pin fan connector (for CPU)
- 1 x PCI 104 connector
|
| On-board RTC | - On-chip RTC with battery back up
- 1 x External Li-Ion battery
- The battery socket is in flat direction.
- Tolerance less than 2 sec ( 24 hours ) under 25°C environment
|
| Storage | - 1 x CF Internal socket, supports One Type I& II Compact Flash Card (Primary Master)
- 1 x IDE 44-pin connector
|
| System Monitor | - Derived from Super I/O to support system voltage, fan speed, temperature monitoring
|
| Power Requirements | - Supports both AT and ATX Mode (Factory default setting is AT mode) CPU: P-M 1.7 G Memory: On board DDR 256 MB:+12V +5V; Full-Loading Mode(A):0.2 A 6.2A; Light loading Mode(A):0.2A 2.5A. NOTE:1.Full Loading: Utilize CPU 100% with Burn-in test running. 2.Light Loading: Utilize CPU loading below 5% without data or application running.
|
| Dimensions | - 3.5" form factor, 146 mm (L) x 105 mm (W) (5.7" x 4.1")
|
| Environment | - Operating temperatures: 0°C to 60°C
- Storage temperatures: -20°C to 85°C
- Relative humidity: Operating 10% to 90%, non-condensing; Non-operating 5% to 95%, non-condensing
|
| Certifications | |